Skip to main content
Automation partner
Marc Fuentes

Author:
Marc Fuentes
VP, Commercial Growth and Operations

Before design freeze, manufacturers should evaluate a greenfield automation partner on six things: process readiness, controls and data architecture, robotics, vision, and tooling integration, simulation, acceptance criteria, and post-launch support. A strong partner proves each one with a deliverable you can inspect, such as a validated digital twin or a written FAT and SAT protocol. Industry fit matters as much, since EV battery, electronics, and life sciences lines carry different tolerances and validation demands. For manufacturing leaders evaluating automation retrofit partners or greenfield integrators, this guide gives you a delivery model comparison, a scoring framework, and a checklist of decisions to lock before the design is frozen.

Why does partner choice need to happen before design freeze?

Design freeze is the point where changes stop being cheap. After it, a late MES requirement or a new gripper means redesign and schedule slip. Capital projects already run hot. A McKinsey survey of senior project executives found that projects overrun their budgets and schedules by 30 to 45 percent on average. Spending keeps rising too: Deloitte reports that 80% of manufacturers plan to put 20% or more of their improvement budgets into smart manufacturing. Choose early, and the team that builds the line also shapes its design.

Key takeaways

  • Answer six questions before design freeze: process readiness, controls and data architecture, robotics, vision, and tooling integration, simulation, acceptance criteria, and post-launch support.
  • Match the delivery model to the risk. Equipment suppliers and cell integrators leave line-level integration with you, while a full-lifecycle partner owns it from concept to ramp.
  • Ask every bidder for the same inspectable deliverables, such as a process FMEA, an OT architecture, a digital twin, and written FAT and SAT protocols.
  • Assign each pre-freeze decision to one owner across engineering, operations, quality, and finance, and tie acceptance targets to payment milestones.
  • Judge industry fit on running lines at your volume in EV battery, electronics, or life sciences production, rather than on robot counts alone.

Which delivery model fits a greenfield project?

Greenfield industrial automation integration usually follows one of three models, and each places risk differently.

Delivery modelTypical scopeWho owns integration riskBest fit
Equipment supplierMachines built to your specificationYou, or a third party you hireStable, single-process steps
Cell integratorOne robotic or vision cell and its controlsShared. Line-level handoffs stay with youAdded capacity or retrofitting manufacturing lines
Full-lifecycle partnerEngineering through support, across the lineThe partner, from concept to ramp-upGreenfield lines and mixed-technology production systems

When robotics, laser welding, machine vision, and precision fixtures share one takt time and one MES, line-level integration decides your launch date.

How should you score an integration partner?

Weight each criterion from 1 to 5, then ask every bidder for the same evidence.

CriterionWhat to ask forRed flag
Process readinessProcess FMEA, cycle time study, and tolerance reviewA quote before anyone studies your parts
Controls and data architecturePLC standards, SCADA and MES interfaces, and OT security designIndustrial IoT deferred until after install
Robotics, vision, and toolingOne owner for robot, vision system, and tooling performanceThree vendors and three warranties
SimulationThroughput simulation and a digital twin used in commissioningSimulation sold as an optional extra
Acceptance criteriaFAT and SAT protocols with OEE, yield, and cycle time targetsAcceptance defined as hours running
Post-launch supportSpares, training, remote support, and a predictive maintenance planSupport scoped after installation

What does credible project evidence look like?

Ask for evidence in your industry, at your volume. Mobility automation integration, from automotive automation services to EV battery lines, calls for cell, module, and pack experience. Electronics needs high-mix changeover. Life sciences automation integration adds IQ, OQ, and PQ validation, and consumer goods automation integration turns on format changeover speed.

The IFR counted 542,000 industrial robots installed in 2024, so most bidders can install robots. Fewer can show a running line that combines robotics, vision systems, and data under one acceptance plan. McKinsey reports that digital twins have cut development times by 20 to 50 percent for some users, and the same models let you test layouts before steel is cut.

Which decisions must be locked before design freeze?

DecisionAccountableLocked when
Product variants, tolerances, and cycle timeEngineeringDrawings and takt time are signed off
Layout, buffers, and staffing modelOperationsSimulation confirms target OEE
Inspection points and traceability dataQualityDefect library and data fields are agreed
Controls, MES, SCADA, and OT securityEngineering with IT/OTArchitecture is approved
Legacy equipment integrationOperations and engineeringInterfaces are tested in simulation
Acceptance targets and payment milestonesFinance with qualityFAT and SAT targets are tied to payments
Total cost of ownershipFinanceSpares, service, and training are priced

How does Eclipse Automation support the full lifecycle?

Eclipse Automation works across the full Factory Automation Lifecycle, and each stage produces something you can review. Advanced Engineering Services defines the process and ROI case before a quote is final. DuPont, CHEP, and Intuitive Surgical each began their work with Eclipse at this stage. Through the Neuron Centre, Eclipse ships every machine, cell, or line simulation-ready, and Eclipse RealitySync lets cross-functional teams review the project in an immersive model built from that digital twin data.

Vertical integration across one million square feet of manufacturing space keeps precision tooling, machining, and assembly under one roof. Its 400 engineers support EV and battery, electronics, life sciences, and consumer products projects, and post-automation support carries the line through ramp-up.

FAQs

Frequently asked questions

What is design freeze in a factory automation project?

Design freeze is the milestone where the line concept, layout, controls architecture, and key equipment are locked so detailed engineering and build can start. Changes after this point cost more and add schedule risk. Advanced Engineering Services helps teams settle these choices early.

When should we bring an integration partner into a greenfield project?

Bring one in during concept and process development, well before design freeze. That gives the partner time to study your parts, run simulation, and flag risks while they are still inexpensive to fix. The Factory Readiness Assessment is a practical starting point.

Can a greenfield line connect to legacy equipment in an existing plant?

Yes, if interfaces are defined before design freeze. Plan the PLC, SCADA, and MES connections up front and test them in a digital twin so legacy equipment integration does not surface as a commissioning surprise.

What should automation acceptance criteria include?

Strong acceptance criteria set measurable targets for cycle time, OEE, first-pass yield, and uptime, and define how FAT and SAT tests will prove them. Tie those targets to payment milestones and to the service and support plan that follows launch.

How does industry fit change the way we evaluate partners?

Each industry brings its own constraints. EV battery lines need weld and inspection control, electronics needs high-mix handling, and life sciences needs validation and traceability. Review a partner’s work in EV and batteries, electronics, or life sciences, along with their case studies.

Explore the possibilities

Evaluating integration partners for your next greenfield line? Book a discovery call to learn how Eclipse Automation supports greenfield line design, simulation, multi-technology integration, and post-launch support.

Related articles and insights

Back to top