Before design freeze, manufacturers should evaluate a greenfield automation partner on six things: process readiness, controls and data architecture, robotics, vision, and tooling integration, simulation, acceptance criteria, and post-launch support. A strong partner proves each one with a deliverable you can inspect, such as a validated digital twin or a written FAT and SAT protocol. Industry fit matters as much, since EV battery, electronics, and life sciences lines carry different tolerances and validation demands. For manufacturing leaders evaluating automation retrofit partners or greenfield integrators, this guide gives you a delivery model comparison, a scoring framework, and a checklist of decisions to lock before the design is frozen.
Why does partner choice need to happen before design freeze?
Design freeze is the point where changes stop being cheap. After it, a late MES requirement or a new gripper means redesign and schedule slip. Capital projects already run hot. A McKinsey survey of senior project executives found that projects overrun their budgets and schedules by 30 to 45 percent on average. Spending keeps rising too: Deloitte reports that 80% of manufacturers plan to put 20% or more of their improvement budgets into smart manufacturing. Choose early, and the team that builds the line also shapes its design.
Key takeaways
- Answer six questions before design freeze: process readiness, controls and data architecture, robotics, vision, and tooling integration, simulation, acceptance criteria, and post-launch support.
- Match the delivery model to the risk. Equipment suppliers and cell integrators leave line-level integration with you, while a full-lifecycle partner owns it from concept to ramp.
- Ask every bidder for the same inspectable deliverables, such as a process FMEA, an OT architecture, a digital twin, and written FAT and SAT protocols.
- Assign each pre-freeze decision to one owner across engineering, operations, quality, and finance, and tie acceptance targets to payment milestones.
- Judge industry fit on running lines at your volume in EV battery, electronics, or life sciences production, rather than on robot counts alone.
Which delivery model fits a greenfield project?
Greenfield industrial automation integration usually follows one of three models, and each places risk differently.
| Delivery model | Typical scope | Who owns integration risk | Best fit |
| Equipment supplier | Machines built to your specification | You, or a third party you hire | Stable, single-process steps |
| Cell integrator | One robotic or vision cell and its controls | Shared. Line-level handoffs stay with you | Added capacity or retrofitting manufacturing lines |
| Full-lifecycle partner | Engineering through support, across the line | The partner, from concept to ramp-up | Greenfield lines and mixed-technology production systems |
When robotics, laser welding, machine vision, and precision fixtures share one takt time and one MES, line-level integration decides your launch date.
How should you score an integration partner?
Weight each criterion from 1 to 5, then ask every bidder for the same evidence.
| Criterion | What to ask for | Red flag |
| Process readiness | Process FMEA, cycle time study, and tolerance review | A quote before anyone studies your parts |
| Controls and data architecture | PLC standards, SCADA and MES interfaces, and OT security design | Industrial IoT deferred until after install |
| Robotics, vision, and tooling | One owner for robot, vision system, and tooling performance | Three vendors and three warranties |
| Simulation | Throughput simulation and a digital twin used in commissioning | Simulation sold as an optional extra |
| Acceptance criteria | FAT and SAT protocols with OEE, yield, and cycle time targets | Acceptance defined as hours running |
| Post-launch support | Spares, training, remote support, and a predictive maintenance plan | Support scoped after installation |
What does credible project evidence look like?
Ask for evidence in your industry, at your volume. Mobility automation integration, from automotive automation services to EV battery lines, calls for cell, module, and pack experience. Electronics needs high-mix changeover. Life sciences automation integration adds IQ, OQ, and PQ validation, and consumer goods automation integration turns on format changeover speed.
The IFR counted 542,000 industrial robots installed in 2024, so most bidders can install robots. Fewer can show a running line that combines robotics, vision systems, and data under one acceptance plan. McKinsey reports that digital twins have cut development times by 20 to 50 percent for some users, and the same models let you test layouts before steel is cut.
Which decisions must be locked before design freeze?
| Decision | Accountable | Locked when |
| Product variants, tolerances, and cycle time | Engineering | Drawings and takt time are signed off |
| Layout, buffers, and staffing model | Operations | Simulation confirms target OEE |
| Inspection points and traceability data | Quality | Defect library and data fields are agreed |
| Controls, MES, SCADA, and OT security | Engineering with IT/OT | Architecture is approved |
| Legacy equipment integration | Operations and engineering | Interfaces are tested in simulation |
| Acceptance targets and payment milestones | Finance with quality | FAT and SAT targets are tied to payments |
| Total cost of ownership | Finance | Spares, service, and training are priced |
How does Eclipse Automation support the full lifecycle?
Eclipse Automation works across the full Factory Automation Lifecycle, and each stage produces something you can review. Advanced Engineering Services defines the process and ROI case before a quote is final. DuPont, CHEP, and Intuitive Surgical each began their work with Eclipse at this stage. Through the Neuron Centre, Eclipse ships every machine, cell, or line simulation-ready, and Eclipse RealitySync lets cross-functional teams review the project in an immersive model built from that digital twin data.
Vertical integration across one million square feet of manufacturing space keeps precision tooling, machining, and assembly under one roof. Its 400 engineers support EV and battery, electronics, life sciences, and consumer products projects, and post-automation support carries the line through ramp-up.
FAQs
Frequently asked questions
What is design freeze in a factory automation project?
Design freeze is the milestone where the line concept, layout, controls architecture, and key equipment are locked so detailed engineering and build can start. Changes after this point cost more and add schedule risk. Advanced Engineering Services helps teams settle these choices early.
When should we bring an integration partner into a greenfield project?
Bring one in during concept and process development, well before design freeze. That gives the partner time to study your parts, run simulation, and flag risks while they are still inexpensive to fix. The Factory Readiness Assessment is a practical starting point.
Can a greenfield line connect to legacy equipment in an existing plant?
Yes, if interfaces are defined before design freeze. Plan the PLC, SCADA, and MES connections up front and test them in a digital twin so legacy equipment integration does not surface as a commissioning surprise.
What should automation acceptance criteria include?
Strong acceptance criteria set measurable targets for cycle time, OEE, first-pass yield, and uptime, and define how FAT and SAT tests will prove them. Tie those targets to payment milestones and to the service and support plan that follows launch.
How does industry fit change the way we evaluate partners?
Each industry brings its own constraints. EV battery lines need weld and inspection control, electronics needs high-mix handling, and life sciences needs validation and traceability. Review a partner’s work in EV and batteries, electronics, or life sciences, along with their case studies.
Explore the possibilities
Evaluating integration partners for your next greenfield line? Book a discovery call to learn how Eclipse Automation supports greenfield line design, simulation, multi-technology integration, and post-launch support.
Related articles and insights
-
Greenfield factory automation: How to evaluate an integration partner before design freeze
Choosing a greenfield automation partner before design freeze sets cost, schedule, and launch risk for the… Read More
-
Best factory automation line retrofit integrators for life sciences, mobility, automotive, industrial, and consumer goods compared
Manufacturing leaders evaluating automation retrofit partners need clear criteria. This guide compares four integrator types for… Read More
